Shop headings: New Spares | Used Spares | Accessories | Brands
A2 stainless steel hex head bolt
Same spec as Guzzi ref. 98074420 but in stainless rather than self colour
More than 5 in stock
98054520 GU98054520 98 05 45 20
9805 4520 9805.4520 98.05.45.20
£1.00
INC VAT
£0.83 EX VAT
Oil pressure sender, M12 thread, male bullet connector
Supercedes Guzzi no. 12768700. Some small twins also require adapter 19055800 (or ELA19720 can be fitted in place of this switch). Check which type your small twin uses before replacing.
See ENA12640 for replacement crush washer if required
More than 5 in stock
17768750 GU17768750 17 76 87 50
1776 8750 1776.8750 17.76.87.50
£10.00
INC VAT
£8.33 EX VAT
Gasket for inlet manifold
More than 5 in stock
28115560-z 28115560 GU28115560 28 11 55 60
2811 5560 2811.5560 28.11.55.60
£1.70
INC VAT
£1.42 EX VAT
O ring, various applications including dipstick on small twins and fork top on Le Mans 1000 and Cali 1100.
More than 5 in stock
90706282 GU90706282 90 70 62 82
9070 6282 9070.6282 90.70.62.82
£1.00
INC VAT
£0.83 EX VAT
Circlip for gudgeon pin
Gudgeon pin clip also known as Guzzi ref. 90351037
More than 5 in stock
27061385 GU27061385 27 06 13 85
2706 1385 2706.1385 27.06.13.85
£8.30
INC VAT
£6.92 EX VAT
M8 zinc finish bolt used for fixing ring gear on 850, 1000 and Cali models (8 bolts required)
Also known as Guzzi ref. 98024420
More than 5 in stock
98054420-z 98054420 GU98054420 98 05 44 20
9805 4420 9805.4420 98.05.44.20
£0.90
INC VAT
£0.75 EX VAT
Captive square M6 nut for fixing bodywork
Used to retain side panels on many models. Similar to chimney nut
More than 5 in stock
92660601 GU92660601 92 66 06 01
9266 0601 9266.0601 92.66.06.01
£1.50
INC VAT
£1.25 EX VAT
Clutch adjustment locknut for gearbox rear, locks adjustment of freeplay on clutch arm. Also used as tappet adjuster nut on early 750 and Nuovo Falcone models
Also known as Guzzi ref. 92606508
More than 5 in stock
92602508 GU92602508 92 60 25 08
9260 2508 9260.2508 92.60.25.08
£0.90
INC VAT
£0.75 EX VAT
8 sided UFI 23 287 00 cartridge oil filter with sealing rubber.
From late 2015 onwards 1200 models used SIA06428
See SIA15301 for alternative filter from Mahle. Please note that Daytona 1000 models where filter screws into base of sump require SIA14530. This is a 8 sided oil filter. Use tool TOA41006 if your filter is located inside the sump, use tool TOA01201 if you change your oil filter without removing the sump
See ENA90948 for the oil filter cover o ring
More than 5 in stock
30153000 GU30153000 30 15 30 00
3015 3000 3015.3000 30.15.30.00
£10.00
INC VAT
£8.33 EX VAT
A2 stainless socket cap screw M5 x 45, used for retaining Bosch alternator stator
More than 5 in stock
98620245 GU98620245 98 62 02 45
9862 0245 9862.0245 98.62.02.45
£1.20
INC VAT
£1.00 EX VAT